FAQs | Find Answers

Search Results

Results 91 - 100 of 110

Recommended Links
  1. LinkStation 420, 421e - How can I replace a hard drive and rebuild a RAID array in the LinkStation?
    [Answer ID: 15146]
    If a drive fails, NAS Navigator2 and Settings will show an error message.Follow this procedure to replace a failed hard drive with a Buffalo Technology OP-HD/LS series drive of the same size or larger capacity(*), available from www.buffalotech.com....
  2. TeraStation 5000 - Using JBOD
    [Answer ID: 15159]
    With JBOD, each hard drive in the TeraStation is addressed separately. To put drives from an array into JBOD mode, follow the steps below.1.In the TeraStation's settings, click to the right of "RAID"....
  3. How to Open Settings
    [Answer ID: 15163]
    Configure and administer your TeraStation using the settings interface, accessible from a browser window. Open the interface using the procedure below or type the TeraStation's IP address in the URL field of your browser. Within Settings, the Easy Admin page gives you quick access to commonly used settings....
  4. LinkStation 400 - You can't see the contents from a DLNA-compatible device
    [Answer ID: 15167]
    If you remove the USB drive without properly dismounting it, you may not see the contents from a DLNA-compatible device, even if you reboot the LinkStation.In such a case, wait for 50 seconds, then follow this procedure to connect a USB drive to a USB port on the LinkStion again and dismount the drive properly....
  5. Surveillance Cameras Troubleshooting
    [Answer ID: 15170]
    IssuePossible CausePossible SolutionVideo recording does not start.Surveillance Camera setting not enabled.Enable the Surveillance Camera from Settings.A LAN cable between the TeraStation and network camera is disconnected, or the power is turned off....
  6. TeraStation 7000 – How to replace a hard drive and rebuild a RAID array in the TeraStation?
    [Answer ID: 15184]
    Hard drives in the TeraStation show a blue status LED during normal operation. When a drive fails, its error LED will glow red. A failed drive whose error LED is glowing red may be hot swapped....
  7. How to Update the Effective Date of NovaBACKUP License
    [Answer ID: 15191]
    Go to the http://www.novastor.com/en/upgrade website to update the effective date of NovaBACKUP license of an OP-LP-NOVA/PRO or OP-LP-NOVA/BE license pack. Enter the License key ("Key Code") from the sheet "NovaBACKUP License Pack GUIDE" and the email address, then click [Enter]. You will get new license key....
  8. WS5000 - How to Get Around the Error "POST ERR:00D9 Boot from HDDx" when the TeraStation Boots
    [Answer ID: 15195]
    When the drive C is in degraded mode, the error "POST ERR:00D9 Boot from HDDx" may be displayed on the LCD panel.To work around the error,  replace the hard drive and repair the volume of the system area in RAID Builder....
  9. An Error May Occur When You Back up the LinkStation or TeraStation in Express Wizard Screen of NovaBACKUP with Windows XP
    [Answer ID: 15196]
    To back up your LinkStation and TeraStation with NovaBACKUP from Windows XP, select "Backup" on the top of the main menu.
  10. When you update the firmware, the message "Updating Firmware" is displayed, but the firmware update never finish.
    [Answer ID: 15200]
    The online update server may be not responding.If the message persists for more than 10 minutes, turn off the LinkStation or TeraStation. Reboot the LinkStation or TeraStation, wait for a while, and update the firmware again....
< Previous  4  5  6  7  8  9  10  11  Next >

Refine your search

Select Product / OS & Hardware

      Enter Keywords or a specified ID